Home Assistant - Revision history

Jeffa: /* Home Assistant Tasmota Integration */ added discord note

2021-09-04T03:10:14Z

‎Home Assistant Tasmota Integration: added discord note

Jeffa: add fine tuning

2021-09-04T03:08:59Z

add fine tuning

Jeffa: Documented first configuration that works for the HA automagions

2021-09-04T02:46:09Z

Documented first configuration that works for the HA automagions

Jeffa: /* Debugging */ add debounce

2021-09-04T01:54:34Z

‎Debugging: add debounce

Jeffa: /* Debugging */ weird linking removed

2021-09-03T22:24:53Z

‎Debugging: weird linking removed

Jeffa: Adding debug section as I try to configure home assistant tasmota integration

2021-09-03T21:45:26Z

Adding debug section as I try to configure home assistant tasmota integration

Jeffa: Add some resources suggested by hass

2018-11-04T03:12:21Z

Add some resources suggested by hass

Jeffa at 03:04, 4 November 2018

2018-11-04T03:04:16Z

Jeffa: Initial creation

2018-11-04T03:00:37Z

Initial creation

New page

{{Blockquote|I'm taking a look at home assistant to aggregate all the IoT stuff I've made.
This page is basically just some notes on how I installed and configured it.
}}

[https://www.home-assistant.io/docs/installation/raspberry-pi/ Manual installation on a Raspberry Pi] "This guide is also referred to as the “Advanced Guide” for a virtual environment install."

[[Category:IoT]]

@@ Line 7: / Line 7: @@
 ==Home Assistant Tasmota Integration==
 <pre>
 HA version    core-2021.9.0 I have a D1 mini that I've had configured in my garage to read a reed switch and to read two DS18B20s a HA automation will illuminate a light when a reed switch GPIO14 switchmode2 on the garage door indicates that garage door is open. This automation has been working a long time, long enough to have some very old firmware that didn't support the new > v9.2 discovery. I've updated the d1 mini to tasmota.bin version  9.5.0 it's reading the DS18B20s and I see MQTT activity when I open / close the garage door. The DS18B20s are discovered but not the switch ???, that is I don't see the switch trigger in the automation editor. I've tried with switchmod114 as 0 or 1. Also tried reloading the Tasmota integration. I've read the https://www.home-assistant.io/integrations/tasmota/ and https://tasmota.github.io/docs/Buttons-and-Switches/ perhaps I missed something? Any thoughts?
@@ Line 41: / Line 42: @@
 ===Resources / Documentation===
 https://www.home-assistant.io/integrations/tasmota/
 ==Other==

@@ Line 31: / Line 31: @@
 :44:47.765 CMD: switchdebounce1
 :44:47.772 MQT: stat/0B5CBE/RESULT = {"SwitchDebounce":90}
+</pre>
+====Fine tuning needed====
 </pre>

← Older revision		Revision as of 02:46, 4 September 2021
Line 19:		Line 19:

	switchdebounce1 90 I had double entries in the log where the switch would indicate in mqtt that it was off followed by an immediate on while door still open, switchdebounce1 90 fixed it.		switchdebounce1 90 I had double entries in the log where the switch would indicate in mqtt that it was off followed by an immediate on while door still open, switchdebounce1 90 fixed it.
		+
		+	===Working Configuration===
		+	<pre>
		+	19:38:11.927 CMD: switchmode1
		+	19:38:11.934 MQT: stat/0B5CBE/RESULT = {"SwitchMode1":1}
		+	mode 2 would be more logical, I fixed the logic in the HA automation.
		+
		+	19:42:48.588 CMD: SetOption114
		+	19:42:48.595 MQT: stat/0B5CBE/RESULT = {"SetOption114":"ON"}
		+
		+	19:44:47.765 CMD: switchdebounce1
		+	19:44:47.772 MQT: stat/0B5CBE/RESULT = {"SwitchDebounce":90}
		+
		+
		+	</pre>

	===Resources / Documentation===		===Resources / Documentation===

← Older revision		Revision as of 01:54, 4 September 2021
Line 17:		Line 17:

	SetOption114 1 - When [https://tasmota.github.io/docs/Buttons-and-Switches/#setoption114 SetOption114] 1 all switches are detached from their respective relays and will send MQTT messages instead in the form of {"Switch<x>":{"Action":"<state>"}}.		SetOption114 1 - When [https://tasmota.github.io/docs/Buttons-and-Switches/#setoption114 SetOption114] 1 all switches are detached from their respective relays and will send MQTT messages instead in the form of {"Switch<x>":{"Action":"<state>"}}.
		+
		+	switchdebounce1 90 I had double entries in the log where the switch would indicate in mqtt that it was off followed by an immediate on while door still open, switchdebounce1 90 fixed it.

	===Resources / Documentation===		===Resources / Documentation===

@@ Line 12: / Line 12: @@
 </pre>
 ===Debugging===
-[[see; https://tasmota.github.io/docs/Buttons-and-Switches/#switchmode-15|SwitchMode1 15]]
+SwitchMode1 15 see; https://tasmota.github.io/docs/Buttons-and-Switches/#switchmode-15|SwitchMode1 15
 SetOption19 0 - turn off mqtt discovery
 SetOption114 1  - When [https://tasmota.github.io/docs/Buttons-and-Switches/#setoption114 SetOption114] 1 all switches are detached from their respective relays and will send MQTT messages instead in the form of {"Switch<x>":{"Action":"<state>"}}.
 ===Resources / Documentation===

@@ Line 2: / Line 2: @@
 This page is basically just some notes on how I installed and configured it.
 I'm installing on a Pine A64+ running Debian Stretch
 }}
 [https://www.home-assistant.io/docs/installation/raspberry-pi/ Manual installation on a Raspberry Pi] "This guide is also referred to as the “Advanced Guide” for a virtual environment install."

← Older revision		Revision as of 03:12, 4 November 2018
Line 5:		Line 5:

	[https://www.home-assistant.io/docs/installation/raspberry-pi/ Manual installation on a Raspberry Pi] "This guide is also referred to as the “Advanced Guide” for a virtual environment install."		[https://www.home-assistant.io/docs/installation/raspberry-pi/ Manual installation on a Raspberry Pi] "This guide is also referred to as the “Advanced Guide” for a virtual environment install."
		+
		+
		+	- Configuring Home Assistant:
		+	https://home-assistant.io/getting-started/configuration/
		+
		+	- Available components:
		+	https://home-assistant.io/components/
		+
		+	- Troubleshooting your configuration:
		+	https://home-assistant.io/getting-started/troubleshooting-configuration/
		+
		+	- Getting help:
		+	https://home-assistant.io/help/
		+



	[[Category:IoT]]		[[Category:IoT]]

@@ Line 1: / Line 1: @@
 {{Blockquote|I'm taking a look at home assistant to aggregate all the IoT stuff I've made.
 This page is basically just some notes on how I installed and configured it.
 }}