Difference between revisions of "Home Assistant"

From Review or Discard at Will
Jump to: navigation, search
(Adding debug section as I try to configure home assistant tasmota integration)
(Debugging: weird linking removed)
Line 12: Line 12:
 
</pre>
 
</pre>
 
===Debugging===
 
===Debugging===
[[see; https://tasmota.github.io/docs/Buttons-and-Switches/#switchmode-15|SwitchMode1 15]]
+
SwitchMode1 15 see; https://tasmota.github.io/docs/Buttons-and-Switches/#switchmode-15|SwitchMode1 15
  
 
SetOption19 0 - turn off mqtt discovery
 
SetOption19 0 - turn off mqtt discovery
  
 
SetOption114 1  - When [https://tasmota.github.io/docs/Buttons-and-Switches/#setoption114 SetOption114] 1 all switches are detached from their respective relays and will send MQTT messages instead in the form of {"Switch<x>":{"Action":"<state>"}}.
 
SetOption114 1  - When [https://tasmota.github.io/docs/Buttons-and-Switches/#setoption114 SetOption114] 1 all switches are detached from their respective relays and will send MQTT messages instead in the form of {"Switch<x>":{"Action":"<state>"}}.
 
 
  
 
===Resources / Documentation===
 
===Resources / Documentation===

Revision as of 15:24, 3 September 2021

I'm taking a look at home assistant to aggregate all the IoT stuff I've made. This page is basically just some notes on how I installed and configured it. I'm installing on a Pine A64+ running Debian Stretch

Years later 9/2/2021 maybe update this a bit. I've recently upgraded firmware on most of my Tasmota devices mostly Sonoff basic and D1 Mini. I'm trying to eleminate some yaml using the > v9.2 HA tasmota integration. These are notes mostly for me. You may find them helpful, or not.

Home Assistant Tasmota Integration

HA version    core-2021.9.0 I have a D1 mini that I've had configured in my garage to read a reed switch and to read two DS18B20s a HA automation will illuminate a light when a reed switch GPIO14 switchmode2 on the garage door indicates that garage door is open. This automation has been working a long time, long enough to have some very old firmware that didn't support the new > v9.2 discovery. I've updated the d1 mini to tasmota.bin version  9.5.0 it's reading the DS18B20s and I see MQTT activity when I open / close the garage door. The DS18B20s are discovered but not the switch ???, that is I don't see the switch trigger in the automation editor. I've tried with switchmod114 as 0 or 1. Also tried reloading the Tasmota integration. I've read the https://www.home-assistant.io/integrations/tasmota/ and https://tasmota.github.io/docs/Buttons-and-Switches/ perhaps I missed something? Any thoughts?

Debugging

SwitchMode1 15 see; https://tasmota.github.io/docs/Buttons-and-Switches/#switchmode-15%7CSwitchMode1 15

SetOption19 0 - turn off mqtt discovery

SetOption114 1 - When SetOption114 1 all switches are detached from their respective relays and will send MQTT messages instead in the form of {"Switch<x>":{"Action":"<state>"}}.

Resources / Documentation

https://www.home-assistant.io/integrations/tasmota/


Other

Manual installation on a Raspberry Pi "This guide is also referred to as the “Advanced Guide” for a virtual environment install."


        - Configuring Home Assistant:
          https://home-assistant.io/getting-started/configuration/
        - Available components:
          https://home-assistant.io/components/
        - Troubleshooting your configuration:
          https://home-assistant.io/getting-started/troubleshooting-configuration/
        - Getting help:
          https://home-assistant.io/help/